No. | Brand | T | M | s | F | H | R | J | a |
61.25.1255.500.11.1503 | Standard 5 | - | - | - | 369 mm | - | - | - | - |
12.20.0895.001.21.1504 | Standard 5 | - | - | - | - | - | - | - | - |
162.25.0886.891.21.1503 | Standard 5 | 54.2 mm | - | - | - | 171.5 mm | - | 143.5 mm | - |
62.20.0844.575.01.1403 | Standard 5 | - | - | - | - | - | - | - | - |
161.25.0886.891.21.1503 | Standard 5 | - | - | - | - | - | - | - | - |
62.25.1077.308.11.1504 | Standard 5 | - | - | - | - | 217.488 mm | - | - | - |
231.20.0900.503 Type 21/1050.1 | Standard 5 | 50.1 mm | - | - | - | 142.5 mm | - | 116.5 mm | - |
61.25.1355.575.11.1403 | Standard 5 | - | - | - | - | - | - | - | - |
161.25.1320.890.11.1503 | Standard 5 | - | - | - | - | - | - | - | 3 mm |
161.25.0886.890.11.1503 | Standard 5 | - | - | - | - | - | - | - | - |
91.30.1415.990.11.1502 | Standard 5 | 60.7 mm | - | - | - | - | - | - | - |
92.20.1006.990.11.1503 | Standard 5 | - | - | - | - | - | - | - | - |
231.21.0975.013 Type 21/1050.1 | Standard 5 | - | - | - | - | - | - | - | - |
62.25.0955.500.11.1503 | Standard 5 | - | - | - | - | - | - | 450 mm | - |
161.25.1180.890.11.1503 | Standard 5 | - | - | - | - | - | - | - | - |
192.20.1250.990.41.1502 | Standard 5 | - | - | - | - | - | - | - | 24 mm |
192.20.1600.990.41.1502 | Standard 5 | - | - | - | - | - | - | - | - |
280.30.1300.013 Type 110/1500. | Standard 5 | - | - | - | - | - | - | - | - |
62.40.1700.007.19.1503 | Standard 5 | - | - | - | - | - | - | - | - |
62.25.0955.575.11.1403 | Standard 5 | - | - | - | - | - | - | - | - |
62.25.1077.304.21.1504 | Standard 5 | - | - | - | - | 244.475 mm | - | - | - |
12.30.1630.001.41.1503 Standard 5 Slewing Ring Bearings | End plug (suffix Y):EPR 14; ba:53.181 mm; Stabilizing ring:SR-24-20; RG:1/2 NPT; R1:79.375 mm; P60°:249 kN; H:257.175 mm; R2:30.163 mm; Cap bolt:5/8-11 UNC; L:419.1 mm; Max. speed for PosiTrac Plus seal:1350 r/min; Da:215.001 mm; Eye bolt:2 x 3/8-16 UNC; P150°:87.2 kN; Cap bolt, SAE grade:8; Ca:67.793 mm; PG:1/4 NPT; Housing:SSAFS 524; Initial grease fill:379.89 g; A1:120.65 mm; |
11.30.1440.190.11.1503 Standard 5 Slewing Ring Bearings | Accessories:No Shield, no Seal; Sealed Speed Rating n3:8500 rpm; Fillet Radius ra:1.00 mm; Basic Dynamic Radial Load Rating C:22500 N; Oil Speed Rating n2:12000 rpm; d:20.000 mm; D:52.0000 mm; Basic Static Radial Load Rating Co:14600 N; B:25.40 mm; Grease Speed Rating n1:8500 rpm; |
191.20.1600.990.41.1502 Standard 5 Slewing Ring Bearings | B:4 mm; Grease:47 000 min-1; Static (Cor):0.432 kN; rs:0.2 mm; D:13 mm; Dynamic (Cr):1.079 kN; Oil:56 000 min-1; Pu:0.020 kN; Bearing designation:619 / 5 ; ra:0.2 max; d:5 mm; da:6.6 min; Da:11.5 max; Weight:0.0025 kg; |
92.20.1146.991.21.1503 Standard 5 Slewing Ring Bearings | Associated spanner (Hook spanner in accordance with DIN 1810):HN 5-6; Recommended tightening torque:4.2 N·m; Mass:0.2 kg; B:20 mm; h:2 mm; Grub (set) / Locking screw size:M 4; d5:49 mm; G:M 30x1.5; d1:48 mm; b:5 mm; d3:50 mm; |
282.30.0975.013 Type 110/1100.2 Standard 5 Slewing Ring Bearings | Permissible sliding velocity v max.:0.5 m/s; d:110 mm; D1:140 mm; Tolerance shaft:e7; Permissible sliding velocity v min.:0 m/s; Coefficient of friction µ max.:0.15; Specific static load factor K0:45 N/mm²; D:130 mm; Specific dynamic load factor K:25 N/mm²; Mass bushing:2.66 kg; Coefficient of friction µ min.:0.08; a:4 mm; h:111.5 mm; α:124 °; B1:8 mm; Tolerance housing:H7; |
62.25.0886.109.21.1504 Standard 5 Slewing Ring Bearings | H2:16.5 mm; N1:15.5 mm; Recommended diameter for attachment bolts, mm G:12 mm; s1:22.2 mm; Recommended tightening torque for grub screw:4 N·m; B:38.1 mm; Basic static load rating C0:11.2 kN; Housing material:Stainless steel; Limiting speed:3800 r/min; J min.:108 mm; Rα:45 °; Mass bearing unit:1.3 kg; Fatigue load limit Pu:0.475 kN; A1:28 mm; RG:1/4-28 UNF; H:82 mm; J:117.5 mm; Hexagonal key size for grub screw N:3.175 mm; |
61.30.1320.000.11.1504 Standard 5 Slewing Ring Bearings | Limiting speed:1100 r/min; Recommended tightening torque for grub screw:16.5 N·m; d:36.513 mm; Thread grub screw G2:3/8-24 UNF; J max.:133 mm; B1:51.1 mm; Recommended diameter for attachment bolts, mm G:12 mm; N4:4 mm; Mass bearing unit:1.5 kg; H2:19 mm; J min.:119 mm; Housing material:Cast iron; J7:15.5 mm; Fatigue load limit Pu:0.655 kN; Recommended diameter for attachment bolts, inch G:0.5 in; |
282.30.0900.013 Type 110/1100.2 Standard 5 Slewing Ring Bearings | d:60.000 mm; Grease Speed Rating n1:3400 rpm; B:54.00 mm; Oil Speed Rating n2:4500 rpm; D:130.0000 mm; Accessories:No Shield, no Seal; Fillet Radius ra:2.00 mm; Sealed Speed Rating n3:3400 rpm; Basic Dynamic Radial Load Rating C:121000 N; Basic Static Radial Load Rating Co:95000 N; |
62.25.0955.575.11.1403 Standard 5 Slewing Ring Bearings | D:160.0000 mm; Grease Speed Rating n1:2600 rpm; Oil Speed Rating n2:3600 rpm; Accessories:No Shield, no Seal,; Sealed Speed Rating n3:2600 rpm; d:75.000 mm; Fillet Radius ra:2.00 mm; Basic Static Radial Load Rating Co:208000 N; Basic Dynamic Radial Load Rating C:187000 N; B:68.30 mm; |
161.25.0980.891.21.1503 Standard 5 Slewing Ring Bearings | Pa:1800 kN; s:23 mm; P90°:3400 kN; J1:200 mm; Q150°:1650 kN; P120°:2500 kN; A:365 mm; P0°:5400 kN; H1:320 mm; Q180°:1430 kN; Ca:198 mm; L:880 mm; H2:115 mm; A2:365 mm; Cap bolt, size:M 30x220; da:341.313 mm; J:750 mm; N1:42 mm; P180°:2800 kN; Q120°:2860 kN; |
60.25.0855.500.11.1503 Standard 5 Slewing Ring Bearings | Cap bolt, SAE grade:8; Da:399.999 mm; A2:368.3 mm; RG:1 NPT; PG:1/4 NPT; P180°:285 kN; P60°:691 kN; Taconite seal:TER 165; R2:46.831 mm; H:473.075 mm; Ca:117.805 mm; L:831.85 mm; Stabilizing ring:SR-44-38; h:79.375 mm; S:4.763 mm; Initial grease fill:2749.95 g; P90°:414 kN; Pa:71.2 kN; P120°:260 kN; End plug (suffix Y):EPR 23; |
280.30.0975.013 Type 110/1100. Standard 5 Slewing Ring Bearings | Threads per inch:12; d3 max.:155.702 mm; d1:114.3 mm; Sleeve:S 26x4.1/2; B4:25.4 mm; B:22.479 mm; B1:95.301 mm; d:130 mm; G:129.692 mm; Hydraulic nut:HMVC 26E; Mass adapter sleeve assembly:3.8 kg; |
162.28.1600.890.11.1503 Standard 5 Slewing Ring Bearings Video