| 91.35.1704.991.41.1502 Standard 5 Slewing Ring Bearings | P60°:94.3 kN; H1:114.3 mm; Da:180 mm; RG:3/8 NPT; P90°:56.5 kN; R2:30.163 mm; Cap bolt:2 x 3/4-10 UNC; Max. speed for Taconite seal:1050 r/min; A1:111.125 mm; Ca:69.799 mm; J min.:295.275 mm; Cap bolt recommended tightening torque:515.2 N·m; P150°:32 kN; ba:38.894 mm; L:387.35 mm; P120°:35.6 kN; Stabilizing ring:2 x SR-1617; Pa:10.5 kN; H2:44.45 mm; Mass pillow block:31.4 kg; |
| 61.40.1600.008.19.1503 Standard 5 Slewing Ring Bearings | Mass inner ring:0.029 kg; F:28 mm; d:22 mm; B:17 mm; r, r1,2 min.:0.3 mm; |
| 162.28.1700.891.21.1503 Standard 5 Slewing Ring Bearings | ra max.:2 mm; da max.:46 mm; d:35 mm; d1 ≈:54.55 mm; Ca min.:3 mm; Calculation factor e:0.31; Da max.:72.5 mm; a:16.181 mm; T:22.75 mm; Basic static load rating C0:73.5 kN; Mass bearing:0.51 kg; Dimension series:2FB; r3,4 min.:1.5 mm; Fatigue load limit Pu:8.3 kN; C:18 mm; D:80 mm; Db min.:74 mm; Basic dynamic load rating C:88.9 kN; Da min.:70 mm; Calculation factor Y0:1.1; |
| 91.25.1310.990.11.1503 Standard 5 Slewing Ring Bearings | A:8 mm; B1:456 mm; d1:630 mm; G2:G 1/8; Hydraulic nut:HMV 134E; d:670 mm; B5:131 mm; B:106 mm; G3:13 mm; d3:850 mm; Mass adapter sleeve assembly:340 kg; G:Tr 670x6; |
| 11.30.1440.191.41.1503 Standard 5 Slewing Ring Bearings | Taconite seal:TER 138; PG:1/4 NPT; Da:359.999 mm; P180°:145 kN; S:4.763 mm; R1:122.237 mm; H:422.275 mm; End plug (suffix Y):EPR 18; ba:91.281 mm; h:69.85 mm; J max.:635 mm; H2:85.725 mm; J1:127 mm; RG:1 NPT; A2:352.425 mm; da:147.637 mm; Ca:129.794 mm; P150°:120 kN; A1:203.2 mm; Mass pillow block:213 kg; |
| 61.25.1455.575.11.1403 Standard 5 Slewing Ring Bearings | Fillet Radius ra:2.50 mm; D:320.0000 mm; Oil Speed Rating n2:1800 rpm; Fillet Radius rb:1.00 mm; Basic Static Radial Load Rating Co:780000 N; B:96.00 mm; Basic Dynamic Radial Load Rating C:475000 N; d:200.000 mm; Grease Speed Rating n1:1500 rpm; |
| 281.30.1175.013 Type 110/1300.1 Standard 5 Slewing Ring Bearings | Sealed Speed Rating n3:2900 rpm; B:18.00 mm; d:95.000 mm; D:130.0000 mm; Basic Dynamic Radial Load Rating C:33800 N; Fillet Radius ra:1.00 mm; Oil Speed Rating Open/Shielded n2:5600 rpm; Accessories:Two Shields; Basic Static Radial Load Rating Co:33500 N; Grease Speed Rating Open/Shielded n1:4800 rpm; |
| 61.25.0980.890.11.1503 Standard 5 Slewing Ring Bearings | Permissible sliding velocity v max.:0.5 m/s; Coefficient of friction µ min.:0.03; B:180 mm; D:180 mm; Mass bushing:1.8 kg; Specific static load factor K0:200 N/mm²; Tolerance housing:H7; d:160 mm; Tolerance shaft:h8; Effective load carrying cross section A:28480 mm²; Coefficient of friction µ max.:0.08; Specific dynamic load factor K:140 N/mm²; Permissible sliding velocity v min.:0 m/s; |
| 62.30.1600.001.21.1504 Standard 5 Slewing Ring Bearings | Grease Speed Rating Open/Shielded n1:3400 rpm; Basic Static Radial Load Rating Co:112000 N; Fillet Radius ra:2.00 mm; Basic Dynamic Radial Load Rating C:128000 N; B:37.00 mm; d:65.000 mm; D:160.0000 mm; Oil Speed Rating Open/Shielded n2:4100 rpm; Accessories:One Shield; |
| 162.36.1700.890.11.1503 Standard 5 Slewing Ring Bearings | Sealing solution:-; Design (sliding contact surface combination):Steel/PTFE sintered; Specific static load factor K0:250 N/mm²; d:50 mm; B:35 mm; Material constant KM:1400; Basic static load rating C0:390 kN; C:28 mm; da max.:56 mm; ra max.:0.6 mm; α:6 °; Lubricant:Maintenance free &nd; r2 min.:1 mm; D:75 mm; Da max.:71 mm; dk:66 mm; Basic dynamic load rating C:156 kN; Mass plain bearing:0.56 kg; |
| 62.25.1455.500.11.1503 Standard 5 Slewing Ring Bearings | Basic Static Radial Load Rating Co:21200 N; D:52.0000 mm; Oil Speed Rating n2:11000 rpm; Accessories:One Shield & Snap-Ri; Basic Dynamic Radial Load Rating C:22900 N; Grease Speed Rating n1:8000 rpm; Sealed Speed Rating n3:8000 rpm; B:22.20 mm; Fillet Radius ra:1.00 mm; d:25.000 mm; |
| 61.25.0980.108.21.1504 Standard 5 Slewing Ring Bearings | R1:79.375 mm; L:466.725 mm; Pa:25.4 kN; Mass pillow block:67.6 kg; H1:152.4 mm; N1:25.4 mm; Housing:SAF 030 KA; A2:206.375 mm; Labyrinth ring:2 x LOR 125; J min.:371.475 mm; R2:36.513 mm; P180°:84.5 kN; Appropriate attachment bolt size G:0.875 in; Initial grease fill:382.73 g; Da:225.001 mm; End plug (suffix Y):EPR 16; H:287.337 mm; Stabilizing ring:2 x SR-0-21; P120°:73.8 kN; ba:56.356 mm; |